Where is the brush bar reset button on my shark vacuum?
The shark brush-bar reset button can be found on the underside of the vacuum.
How do you troubleshoot a shark vacuum?
Check for a clogged hose or filter; unclog the hose and replace the filter. Wait 45 minutes for the vacuum to cool; then plug in the vacuum. Turn the power switch to the “I-On” position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
How do I clean my shark Navigator canister?
Open both ends of the dirt canister over a trash can and dump out whatever is in there. Now take the canister to a sink of warm soapy water. Open both ends of the dust canister and put it right into that warm bath. Using a long-handled brush or a rag, get inside that canister and scrub it clean.
Is there a reset button on a Shark Navigator vacuum?
To reset the shark vacuum, put the Power button on the On-Off position and keep the vacuum unplugged. If necessary, clear the hose. Plug the vacuum in again after it cools completely.
Why isn’t the brush on my vacuum spinning?
A broken drive belt, damaged brush roll, jammed brush roll bearings, tripped brush roll motor overload, failed brush roll motor or a wiring failure in the wand or nozzle can prevent the brush roll from spinning. Check the condition of the drive belt and replace the belt if it’s worn or broken.
Can you rinse shark HEPA filter?
Many Shark vacuum owners ask: can you wash Shark vacuum filters? Yes, you can wash Shark vacuum filters. In fact, according to the manufacturer, the primary filter should be washed once every month, while the HEPA filter should be washed once every year. You should rinse them with cold water only.
Can you wash the filter in a shark vacuum?
To clean foam and felt filters, simply tap off loose dirt, then rinse them under a tap. Only use water – do not use soap. Always let the filters air dry completely before reinserting them. Hand wash with water and allow to air dry completely before reinserting into the frame and returning to the vacuum.
Why did my vacuum suddenly stop working?
It might sound simple, but lack of power is often the cause of a vacuum cleaner that won’t work. Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don’t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem.
Can I rinse out my shark canister?
Empty the Dust Canister Soak the canister in soapy water and wash it using your microfiber cloth. Rinse it in cold water and allow it to air-dry. Be sure the canister is completely dry before reassembly. This may take around 24 hours.
How to use shark navigator upright vacuum?
Using the Vacuum Cleaning with the Vacuum Accessories Your Shark® Navigator™ Upright Vacuum is a versatile tool that can be used to clean bare floor surfaces or carpets – with the click Secure Super of a switch. Stand the vacuum into the upright position. Plug in the vacuum. 1 Start with the Power Switch in the “O – Off” position.
What are the electrical specifications of the nv100 26?
This manual covers model: NV100 26 TECHNICAL SPECIFICATIONS Voltage: 120V. Watts: 700W Amps: 5.83A Hertz: 60Hz NV100_26_IB_ENG_110317_2.indd 2-1 11-03-17 10:40 AM
How do I Reset my shark navigator™ motor?
Your ®Shark Navigator™is equipped with a protective Motor Thermostat. If the motor should overheat, the thermostat shuts off the power. TO RESET PET/UPHOLSTERYTHE MOTOR THERMOSTAT: Press the Power Button ( )to turn the unit “Off”. Unplug the vacuum. Check for clogged hose or filter; unclog hose and replace filter.
How do I start my shark clean vacuum?
Press the Power Switch ( ) to start the vacuum. NOTE: If vacuum still does not start, contact Customer Service at: 1-800-798-7398. To order Additional Parts & Accessories go to www.sharkclean.com. PART PART NO.